Wilkommen bei Arfert und Loose GbR -

Brother DCP–8080 8085 MFC-8480 8880 8890

Brother DCP–8080 8085 MFC-8480 8880 8890 - Fehler, Error Codes, Fehlermeldungen, Systemfehler

 

Systemfehler Fehler Error Brother DCP–8080 8085 MFC-8480 8880 8890

 

Error 1E = The drum unit reached its life and requires replacement.

Error 1F = Two or more optio l trays are installed

Error 24 = Inter l temperature sensor failure

Error 35 = EEPROM of main PCB failure

Error 36 = HVPS PCB during standby failure

Error 3B = Main PCB RAM failure

Error 3C = EEPROM writing error (Not applicable)

Error 3D = EEPROM reading error (Not applicable)

Error 3E = EEPROM bus error (Not applicable)

Error 44 = No toner cartridge

Error 50 = The drum unit reached its life and requires replacement.

Error 51 = The paper feed kit MP reached its life and requires replacement.

Error 52 = The paper feed kit T1 reached its life and requires replacement.

Error 53 = The paper feed kit T2 reached its life and requires replacement.

Error 54 = The fuser unit reached its life and requires replacement.

Error 55 = The laser unit reached its life and requires replacement.

Error 56 = Back cover is opened

Error 57 = Paper jam (Duplex tray)

Error 58 = Fuser unit failure

Error 59 = Fuser unit failure (Detect fuser failure at start-up)

Error 63 = Toner life end

Error 67 = Toner low

Error 68 = Temperature rise when heater is off

Error 69 = Mis-connect center thermistor connector

Error 6A = Fuser temperature does not reach 60°C within the specified time (center thermistor)

Error 6B = Fuser temperature does not reach 100°C within the specified time (center thermistor)

Error 6C = Fuser temperature exceeds its higher limit (center thermistor)

Error 6D = Fuser temperature exceeds its lower limit (center thermistor)

Error 6E = Fuser temperature does not rise (center thermistor)

Error 6F = Hardware detects extremely high temperature of the center or side thermistors

Error 70 = Fuser motor error

Error 71 = Laser unit polygon motor failure

Error 75 = Sensor of the inside temperature for detection detected higher than normal temperature

Error 76 = Rapid temperature rising failure (center thermistor)

Error 78 = Rapid temperature falling failure (center thermistor)

Error 7A = No detection of main motor synchronous sig l

Error 7D = Dirt on coro wire (detect discharge error)

Error 7F = Fax paper setting mismatch (The setting paper becomes besides the A4/Letter/Legal/Folio) (Not applicable

 

Error 80 = Fax paper size is incorrect (The paper is smaller 10mm than the letter size (11inch) in Fax List/Report

 

Error 83 = Failure of discharge detection (Printing becomes u ble until the drum is replaced with a new one.) (Discharge detection becomes u ble until the drum counter reaches the double of the drum life.

 

Error 84 = Paper jam

Error 85 = Tray 1 is not installed into the machine

Error 86 = Tray 2 is not installed into the machine

Error 88 = Paper jam inside the machine

Error 89 = Incorrect paper size in duplex printing

Error 8A = Paper jam in Tray 1

Error 8B = Paper jam in Tray 2

Error 8C = Paper jam in MP Tray

Error 8D = Paper jam near eject tray

Error 99 = Specified paper size is not supported for duplex printing (Duplex)

Error 9F = Paper empty

Error A1 = Front cover opened

Error A2 = During scanning, 90 cm or longer of a document is detected

Error A3 = Document rear sensor is not turned on when feeding the document

Error A4 = ADF cover opened A5 Fax scanning error (Warning) (First time Error A6 = Fax scanning error (Error) (Second time

 

Error A7 = Scanning color parameter file failure

Error A8 = Scanning color parameter matching error

Error AD = DMA transfer error

Error AE = Document scanner home position sensor is not turned on.

Error AF = Document scanner home position sensor is not turned off.

Error B0 = Document scanner unit FFC detection error

Error B1 = Dark level offset data level error for scanning

Error B2 = Gain control data level error for scanning

Error B7 = A/D converter standard voltage failure; at High side

Error B8 = A/D converter standard voltage failure; at Low side

Error B9 = Scanning light adjustment error is detected

Error BB = White level data error

Error BD = Black level data error

Error BF = ADF duplex scanning cannot be implemented due to too long document

Error C0 = New toner detection lever failure

Error C7 = Insufficient DIMM Memory

Error C8 = Secure print data full

Error C9 = DIMM error

Error CA = Excess current to USB device that is front side of the machine

Error CD = Drum unit is not installed into the machine

Error D1 = Modem initialization failed

Error DD = Fuser error other than 58, 59, 68, 69, 6A, 6B, 6C, 6D, 6E, 6F, 76, 78, DE and E2 are occurre

 

Error DE = Central temperature of heat roller detected the temperature that was lower than 60°C)

 

Error E0 = Program error

Error E1 = Main PCB failure

Error E2 = Central temperature of heat roller exceeds 280°C

Error E6 = EEPROM error

Error EB = The data reading error for E2PROM

Error EC = Fuser fan failure

Error ED = Wireless LAN connection failure between W-LAN PCB and access point

Error EE = Wireless LAN is u ble to communicate between W-LAN PCB and access point

Error EF = LVPS PCB failure

Error F8 = Battery connection error

Error F9 = EEPROM customizing code error

Error FF = Excess current to USB HOST PCB error